Habe ich gerade ausprobiert. Das dämliche Windows wollte dann ein Update machen, das schlug irgendwie fehl. Nach ~ 10 Neustarts mit "bitte warten Windows wird vorbereitet"-Mist hab ich nun noch mal einen Test laufen lassen. Selbes Ergebnis wie zuvor...
So wie ich es sehe bestell ich mir lieber mal eine SSD :/
Your hard disk is a SAMSUNG HD204UI with firmware 1AQ10001.
The average temperature for this hard disk model is 30°C (min=22°C max=40°C) and yours is 36°C.
Troubled attributes:
Attribute Spin Up Time is failing now! Its current value is 1, the worst value was 1 and the threshold is 25. According to the manufacturer, this is a pre-failure condition.
WARNING : your hard disk Spin Up Time attribute current value (1) is below the normal range (66 - 76) reported for your specific hard disk model. Recently purchased hard disks that were not yet power cycled many times might experience a low value here and it wouldn't be a problem as, after some time, the value should raise towards better ones. If, on the other side, your hard disk is not that new and it was powered on several times this might mean its mechanic is getting old. According to Power Cycle Count attribute, your hard disk was powered on 1676 times and this seems to indicate that your hard disk is not brand new and that some kind of drive's mechanic poorer performance is occurring. Usually this attribute is not so relevant by itself, but it might reinforce some other deduction when looking at the global picture.
NOTE : your hard disk Power Cycle Count attribute current value (99) is below the normal range (100 - 100) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.
The overall fitness for this drive is 0%.
The overall performance for this drive is 90%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
The average temperature for this hard disk model is 30°C (min=22°C max=40°C) and yours is 36°C.
Attribute | Current | Raw | ||||
---|---|---|---|---|---|---|
| Raw Read Error Rate | 100 | 000000000004 | |||
| Throughput Performance | 252 | 000000000000 | |||
| Spin Up Time | 1 | 00000000A6AE | |||
| Start/Stop Count | 99 | 000000000680 | |||
| Reallocated Sector Count | 252 | 000000000000 | |||
| Seek Error Rate | 252 | 000000000000 | |||
| Seek Time Performance | 252 | 000000000000 | |||
| Power On Hours Count | 100 | 000000000F44 | |||
| Spin Retry Count | 252 | 000000000000 | |||
| Calibration Retry Count | 252 | 000000000000 | |||
| Power Cycle Count | 99 | 00000000068C | |||
| Unknown attribute 181 | 100 | 000000EE5A09 | |||
| GSense Error Rate | 100 | 00000000005B | |||
| Power Off Retract Count | 252 | 000000000000 | |||
| Hardware ECC Recovered | 100 | 000000000000 | |||
| Reallocated Event Count | 252 | 000000000000 | |||
| Current Pending Sector | 252 | 000000000000 | |||
| Offline Uncorrectable Sector Count | 252 | 000000000000 | |||
| Ultra DMA CRC Error Rate | 200 | 000000000000 | |||
| Write Error Rate | 100 | 000000000014 | |||
| Load Retry Count | 252 | 000000000000 | |||
| Load Cycle Count | 100 | 00000000068F |
Troubled attributes:
Attribute Spin Up Time is failing now! Its current value is 1, the worst value was 1 and the threshold is 25. According to the manufacturer, this is a pre-failure condition.
WARNING : your hard disk Spin Up Time attribute current value (1) is below the normal range (66 - 76) reported for your specific hard disk model. Recently purchased hard disks that were not yet power cycled many times might experience a low value here and it wouldn't be a problem as, after some time, the value should raise towards better ones. If, on the other side, your hard disk is not that new and it was powered on several times this might mean its mechanic is getting old. According to Power Cycle Count attribute, your hard disk was powered on 1676 times and this seems to indicate that your hard disk is not brand new and that some kind of drive's mechanic poorer performance is occurring. Usually this attribute is not so relevant by itself, but it might reinforce some other deduction when looking at the global picture.
NOTE : your hard disk Power Cycle Count attribute current value (99) is below the normal range (100 - 100) reported for your specific hard disk model. Basically your hard disk was power cycled more times than the maximum number the average hard disk was. Power cycles put some stress on the hard disk mechanic. Sometimes power cycles can be caused by a loose hard disk power connector. Make sure it is properly fastened.
The overall fitness for this drive is 0%.
The overall performance for this drive is 90%.
The link to get back and see a new report about this hard disk in the future is this. Consider that new hard disks and new checks are added over time.
So wie ich es sehe bestell ich mir lieber mal eine SSD :/