WPS funktioniert unter Android und mit Alfa AWUS036NEH sowie Intel AGN nicht

  • Ersteller Ersteller gelöschter Benutzer
  • Erstellt am Erstellt am
Jump to last post
G

gelöschter Benutzer

Guest
Hallo Leute,

Ich habe hier ein Arch Linux mit Kernel 3.11.3-1-ck (x86_64) laufen und das folgende Problem: Während ich mit meinem Android-Handy (Galaxy S3 mit Cyanogenmod 10.1.2) einwandfrei auf WPS-aktivierte Netzwerke zugreifen und mich authentifizieren kann, sehe ich mit wash (aus dem reaver-Paket) weder irgendwelche WPS-Netzwerke noch kann ich mich natürlich verbinden.
Auch der NetworkManager vermag mir keine WPS-Netze anzuzeigen.

Dabei habe ich sowohl die interne Karte meines Thinkpad T400 (Intel PRO/Wireless 5100 AGN [Shiloh]), als auch den externen USB-Adapter (Alfa AWUS036NEH mit Ralink-Chipsatz [rt2800usb]) ausprobiert.

Wie kann ich meinen Laptop dazu bringen, die WPS-Funktionalität zu erkennen und diese nutzen?
 
Taucht es bei einem Scan über die Konsole auf?

Schau mal in die Beschreibung des Wifi Moduls, ggf. wurde bei diesem WPS weggelassen.
 
  • Thread Starter Thread Starter
  • #3
You do not have permission to view link please Anmelden or Registrieren
Meinst du bei der Beschreibung das, was bei iw list kommt?
Code:
Expand Collapse Copy 
~ ❯❯❯ iw list
Wiphy phy1
	max # scan SSIDs: 4
	max scan IEs length: 2257 bytes
	Coverage class: 0 (up to 0m)
	Device supports RSN-IBSS.
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP (00-0f-ac:4)
	Available Antennas: TX 0 RX 0
	Supported interface modes:
		 * IBSS
		 * managed
		 * AP
		 * AP/VLAN
		 * WDS
		 * monitor
		 * mesh point
	Band 1:
		Capabilities: 0x172
			HT20/HT40
			Static SM Power Save
			RX Greenfield
			RX HT20 SGI
			RX HT40 SGI
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			No DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 2 usec (0x04)
		HT RX MCS rate indexes supported: 0-7, 32
		TX unequal modulation not supported
		HT TX Max spatial streams: 1
		HT TX MCS rate indexes supported may differ
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 2412 MHz [1] (20.0 dBm)
			* 2417 MHz [2] (20.0 dBm)
			* 2422 MHz [3] (20.0 dBm)
			* 2427 MHz [4] (20.0 dBm)
			* 2432 MHz [5] (20.0 dBm)
			* 2437 MHz [6] (20.0 dBm)
			* 2442 MHz [7] (20.0 dBm)
			* 2447 MHz [8] (20.0 dBm)
			* 2452 MHz [9] (20.0 dBm)
			* 2457 MHz [10] (20.0 dBm)
			* 2462 MHz [11] (20.0 dBm)
			* 2467 MHz [12] (20.0 dBm) (passive scanning, no IBSS)
			* 2472 MHz [13] (20.0 dBm)
			* 2484 MHz [14] (20.0 dBm) (passive scanning, no IBSS)
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * start_ap
		 * new_station
		 * new_mpath
		 * set_mesh_config
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * set_tx_bitrate_mask
		 * frame
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * set_wds_peer
		 * probe_client
		 * set_noack_map
		 * register_beacons
		 * start_p2p_device
		 * Unknown command (92)
		 * connect
		 * disconnect
	Supported TX frame types:
		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
	Supported RX frame types:
		 * IBSS: 0x40 0xb0 0xc0 0xd0
		 * managed: 0x40 0xd0
		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * mesh point: 0xb0 0xc0 0xd0
		 * P2P-client: 0x40 0xd0
		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * P2P-device: 0x40 0xd0
	software interface modes (can always be added):
		 * AP/VLAN
		 * monitor
	valid interface combinations:
		 * #{ AP, mesh point } <= 8,
		   total <= 8, #channels <= 1
	HT Capability overrides:
		 * MCS: ff ff ff ff ff ff ff ff ff ff
		 * maximum A-MSDU length
		 * supported channel width
		 * short GI for 40 MHz
		 * max A-MPDU length exponent
		 * min MPDU start spacing
	Device supports TX status socket option.
	Device supports HT-IBSS.
	Device supports low priority scan.
	Device supports scan flush.
	Device supports AP scan.
Wiphy phy0
	max # scan SSIDs: 20
	max scan IEs length: 195 bytes
	Coverage class: 0 (up to 0m)
	Device supports RSN-IBSS.
	Supported Ciphers:
		* WEP40 (00-0f-ac:1)
		* WEP104 (00-0f-ac:5)
		* TKIP (00-0f-ac:2)
		* CCMP (00-0f-ac:4)
	Available Antennas: TX 0 RX 0
	Supported interface modes:
		 * IBSS
		 * managed
		 * monitor
	Band 1:
		Capabilities: 0x1072
			HT20/HT40
			Static SM Power Save
			RX Greenfield
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		TX unequal modulation not supported
		HT TX Max spatial streams: 1
		HT TX MCS rate indexes supported may differ
		Bitrates (non-HT):
			* 1.0 Mbps
			* 2.0 Mbps (short preamble supported)
			* 5.5 Mbps (short preamble supported)
			* 11.0 Mbps (short preamble supported)
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 2412 MHz [1] (15.0 dBm)
			* 2417 MHz [2] (15.0 dBm)
			* 2422 MHz [3] (15.0 dBm)
			* 2427 MHz [4] (15.0 dBm)
			* 2432 MHz [5] (15.0 dBm)
			* 2437 MHz [6] (15.0 dBm)
			* 2442 MHz [7] (15.0 dBm)
			* 2447 MHz [8] (15.0 dBm)
			* 2452 MHz [9] (15.0 dBm)
			* 2457 MHz [10] (15.0 dBm)
			* 2462 MHz [11] (15.0 dBm)
			* 2467 MHz [12] (15.0 dBm) (passive scanning, no IBSS)
			* 2472 MHz [13] (15.0 dBm) (passive scanning, no IBSS)
	Band 2:
		Capabilities: 0x1072
			HT20/HT40
			Static SM Power Save
			RX Greenfield
			RX HT20 SGI
			RX HT40 SGI
			No RX STBC
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 4 usec (0x05)
		HT RX MCS rate indexes supported: 0-15, 32
		TX unequal modulation not supported
		HT TX Max spatial streams: 1
		HT TX MCS rate indexes supported may differ
		Bitrates (non-HT):
			* 6.0 Mbps
			* 9.0 Mbps
			* 12.0 Mbps
			* 18.0 Mbps
			* 24.0 Mbps
			* 36.0 Mbps
			* 48.0 Mbps
			* 54.0 Mbps
		Frequencies:
			* 5180 MHz [36] (15.0 dBm) (passive scanning, no IBSS)
			* 5200 MHz [40] (15.0 dBm) (passive scanning, no IBSS)
			* 5220 MHz [44] (15.0 dBm) (passive scanning, no IBSS)
			* 5240 MHz [48] (15.0 dBm) (passive scanning, no IBSS)
			* 5260 MHz [52] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5280 MHz [56] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5300 MHz [60] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5320 MHz [64] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5500 MHz [100] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5520 MHz [104] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5540 MHz [108] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5560 MHz [112] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5580 MHz [116] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5600 MHz [120] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5620 MHz [124] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5640 MHz [128] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5660 MHz [132] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5680 MHz [136] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5700 MHz [140] (15.0 dBm) (passive scanning, no IBSS, radar detection)
			  DFS state: usable (for 38396 sec)
			* 5745 MHz [149] (15.0 dBm) (passive scanning, no IBSS)
			* 5765 MHz [153] (15.0 dBm) (passive scanning, no IBSS)
			* 5785 MHz [157] (15.0 dBm) (passive scanning, no IBSS)
			* 5805 MHz [161] (15.0 dBm) (passive scanning, no IBSS)
			* 5825 MHz [165] (15.0 dBm) (passive scanning, no IBSS)
	Supported commands:
		 * new_interface
		 * set_interface
		 * new_key
		 * start_ap
		 * new_station
		 * new_mpath
		 * set_mesh_config
		 * set_bss
		 * authenticate
		 * associate
		 * deauthenticate
		 * disassociate
		 * join_ibss
		 * join_mesh
		 * remain_on_channel
		 * set_tx_bitrate_mask
		 * frame
		 * frame_wait_cancel
		 * set_wiphy_netns
		 * set_channel
		 * set_wds_peer
		 * probe_client
		 * set_noack_map
		 * register_beacons
		 * start_p2p_device
		 * Unknown command (92)
		 * connect
		 * disconnect
	Supported TX frame types:
		 * IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
		 * P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
	Supported RX frame types:
		 * IBSS: 0x40 0xb0 0xc0 0xd0
		 * managed: 0x40 0xd0
		 * AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * mesh point: 0xb0 0xc0 0xd0
		 * P2P-client: 0x40 0xd0
		 * P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
		 * P2P-device: 0x40 0xd0
	software interface modes (can always be added):
		 * monitor
	interface combinations are not supported
	HT Capability overrides:
		 * MCS: ff ff ff ff ff ff ff ff ff ff
		 * maximum A-MSDU length
		 * supported channel width
		 * short GI for 40 MHz
		 * max A-MPDU length exponent
		 * min MPDU start spacing
	Device supports TX status socket option.
	Device supports HT-IBSS.
	Device supports scan flush.
... oder das, was bei dem WLAN-Kernelmodul mit modinfo kommt?
Code:
Expand Collapse Copy 
~ ❯❯❯ modinfo rt2800usb
filename:       /lib/modules/3.11.3-1-ck/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko.gz
license:        GPL
firmware:       rt2870.bin
description:    Ralink RT2800 USB Wireless LAN driver.
version:        2.3.0
author:         http://rt2x00.serialmonkey.com
srcversion:     8D972A7DDE6652BA484C8AE
alias:          usb:vF201p5370d*dc*dsc*dp*ic*isc*ip*in*
alias: [...]

depends:        rt2x00lib,rt2800lib,rt2x00usb,usbcore
intree:         Y
vermagic:       3.11.3-1-ck SMP preempt mod_unload modversions 
parm:           nohwcrypt:Disable hardware encryption. (bool)

filename:       /lib/modules/3.11.3-1-ck/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko.gz
license:        GPL
description:    Ralink RT2800 library
version:        2.3.0
author:         http://rt2x00.serialmonkey.com, Bartlomiej Zolnierkiewicz
srcversion:     26219235502295A1CDE028F
depends:        rt2x00lib,mac80211,crc-ccitt
intree:         Y
vermagic:       3.11.3-1-ck SMP preempt mod_unload modversions 

~ ❯❯❯ modinfo rt2x00lib
filename:       /lib/modules/3.11.3-1-ck/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko.gz
license:        GPL
description:    rt2x00 library
version:        2.3.0
author:         http://rt2x00.serialmonkey.com
srcversion:     8AE9D454A710B1C25F9F518
depends:        mac80211,cfg80211
intree:         Y
vermagic:       3.11.3-1-ck SMP preempt mod_unload modversions

Und was meinst du bei dem Scan über die Konsole? Habe mit wash und iwlist gescannt, beides mal kein WPS angezeigt.

EDIT: Okay, also Kali Linux auf dem selben Rechner erkennt bei beiden Adaptern WPS. Warum, habe ich bisher nicht rausfinden können. Wie mache ich das?
 
Zuletzt bearbeitet:
Du musst dich einloggen oder registrieren, um hier zu antworten.
Zurück
Oben