sia
gesperrt
Hi Leute,
WD Red sind ja für Dauerbetrieb ausgelegt, aber es gibt in meinem Einsatzszenario sehr lange Zeiten komplett ohne Zugriffe auf die Datenpartition.
Daher würde ich gerne ein wenig Strom sparen. Mit hdparm kann man ja theoretisch Stromsparmodi setzen – habe dazu in der /etc/hdparm.conf testweise folgendes eingetragen:
Aber irgendwie schalten die Dinger sich nicht nach 60s ab. Unterstützen WD Red kein Spindown? Wie schaffe ich es in Debian, die Festplatten bei Nichtbenutzung herunterzufahren? Google-Fu heute leider nicht vorhanden.
EDIT:
Gleich mal ausprobieren. Wie ich es liebe, Forenposts zu erstellen, nur um durch das Herunterschreiben des Problems selbst auf andere Suchbegriffe und Lösungsansätze zu stoßen
EDIT2: Die Downloadlinks für das Firmware-Update-Tool musste ich etwas suchen, hier sind sie:
http://download.wdc.com/sata/wd5741x32
http://download.wdc.com/sata/wd5741x64
segfault'ed leider – jemand ne Ahnung, was da das Problem sein könnte?
WD Red sind ja für Dauerbetrieb ausgelegt, aber es gibt in meinem Einsatzszenario sehr lange Zeiten komplett ohne Zugriffe auf die Datenpartition.
Daher würde ich gerne ein wenig Strom sparen. Mit hdparm kann man ja theoretisch Stromsparmodi setzen – habe dazu in der /etc/hdparm.conf testweise folgendes eingetragen:
Code:
/dev/disk/by-id/ata-WDC_WD40EFRX-68WT0N0_WD-WCC4E8754983 {
spindown_time = 12
}
Aber irgendwie schalten die Dinger sich nicht nach 60s ab. Unterstützen WD Red kein Spindown? Wie schaffe ich es in Debian, die Festplatten bei Nichtbenutzung herunterzufahren? Google-Fu heute leider nicht vorhanden.
EDIT:
withblue.ink/2016/07/15/what-i-learnt-from-using-wd-red-disks-to-build-a-home-nas.html schrieb:The issue above has been patched in more recent units. However, as a consequence of this buggy firmware, on the two WD Red disks that I recycled from my previous NAS, the Load Cycle Count was quite high.
As you can see from my data above, the newer drive shipped with a firmware already tweaked to fix the issue. However, if your drives are older (or you just purchased a unit that had been stocked for a while), do not despair: there is a quick and easy fix! Acknowledging the issue, WD released a simple utility to alter the behaviour of the firmware, and wait longer before unloading the heads.
Code:sudo ./wd5741x## -? <-- (## = 32 or 64)
[…]
WD Red drives are optimized for NAS usage, which means they’re designed to run reliably 24/7 and tune power consumption dynamically, and for this reason they do not include a standby function. This is not a bad idea per se: as everyone can tell you, spinning disks up and down constantly is bad for their health. Many home NAS servers, however, are used for a few hours a day only, and stay completely inactive for the rest of the time. In this case, it would probably be safe to spin the disks down and save power (and the environment will thank you!).
On Linux, the traditional way to control disk standby (and power management) is to use hdparm; however, hdparm will not work with WD Red drives, because the firmware of the disks doesn’t support that. Instead, we can use the third-party hd-idle utility to accomplish this.
Gleich mal ausprobieren. Wie ich es liebe, Forenposts zu erstellen, nur um durch das Herunterschreiben des Problems selbst auf andere Suchbegriffe und Lösungsansätze zu stoßen
EDIT2: Die Downloadlinks für das Firmware-Update-Tool musste ich etwas suchen, hier sind sie:
http://download.wdc.com/sata/wd5741x32
http://download.wdc.com/sata/wd5741x64
segfault'ed leider – jemand ne Ahnung, was da das Problem sein könnte?
Zuletzt bearbeitet: